收藏本站
Installation and Operation
2.3.4
Power Good (PWRGD)
The Power Good (PWRGD) output pin has the ability to be pulled up to either SHDN
or V OUT . Populating R2 (and removing R4) with the desired pull-up resistor causes
PWRGD to be pulled up to V OUT . Populating R4 (and removing R2) with the desired
pull-up resistor causes PWRGD to be pulled up to V IN .
When PWRGD is pulled up to V OUT , the device current will be minimal when SHDN is
active. When PWRGD is pulled up to V IN , the device current will be higher when when
SHDN is active because the current will flow threw R4 and the PWRGD pin to ground.
When low operating currents are critical, PWRGD should be pulled up to V OUT . That
will keep current consumption at a minimum when SHDN is active because the output
voltage will be low.
2.3.5
Load Resistance
R5 is used to set the desired load value. Jumper JP4 is used to connect or disconnect
the load resistance to the output.
2.3.6
Line Step
Dynamic Line Step response may be evaluated by connecting an electronically
switched input voltage to testpoints TP1(+) and TP2(-) or to connector J1. An
oscilloscope is connected to TP3 (Ch1 Trigger), TP9 (Ch2) and TP10 (GND). An
appropriate load is selected using R5 and JP4. The input voltage is then electronically
switched from a low voltage to a high voltage. The corresponding voltage waveform
data of the voltage regulator response is captured by the oscilloscope. Microchip will
be offering a Line Step module that connects directly to connector J1. The Line Step
module will be capable of switching between two voltage levels that the user supplies
2.3.7
Load Step
Dynamic Load Step response may be evaluated by connecting an electronically
switched load to testpoints TP9(+) and TP10(-) or to connector P1. An oscilloscope is
connected to the electronic load switch signal (Ch1 Trigger) and to TP9(Ch2) and
TP10(GND). The load is then electronically switched from a high resistance to a low
resistance. The corresponding voltage waveform data of the voltage regulator
response is captured by the oscilloscope. Microchip will be offering a Load Step module
that connects directly to connector P1. The Load Step module will have several
selectable load values populated onboard to cover a wide range of loads. The load will
have the ability to be electronically or manually switched.
2.3.8
Power Supply Rejection Ratio (PSRR)
Power Supply Rejection Ratio tests are performed by removing the input capacitor
jumper, JP1, and connecting an appropriate PSRR analyzer to the SOT23-5 Voltage
Regulator Evaluation Board. The PSRR analyzer may then sweep the input voltage
frequencies and record the corresponding output voltages.
? 2009 Microchip Technology Inc.
DS51811A-page 11
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SP5004EGP SUPERPRO 5004EGP PROGRAMMER
SP7121EK-L IC LED DRVR BACKLIGHT SOT23-6
SP7600EN2-L IC LED DRVR PWM STP-DWN 8HNSOIC
SPB2 PANEL SWING KIT
SPIKECUBE SURGE SUPPRESSR 1OUT DIRECT PLUG
SPIKESTIK SURGE SUPPRESSOR SPIKE STIK 6OUT
SPS-615-HG SURGE SUPP 6OUT 15'CORD HOSP GRD
SR202 SHELF FIXED 4-POST HEAVY DUTY
相关代理商/技术参数
SOT23-5PIN 制造商:IRF 制造商全称:International Rectifier 功能描述:Package Dimensions
SOT-23-6 制造商:RICOH 制造商全称:RICOH electronics devices division 功能描述:SOT-23-6 (SC-74)
SOT23-6 制造商:ZETEX 制造商全称:ZETEX 功能描述:Thermal Resistance and Derating Information
SOT23-6L 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:LOW VOLTAGE 4ohm SPDT SWITCH
SOT23-8L 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:DUAL BILATERAL SWITCH
SOT23-DIP_DS2 制造商:Distributed By MCM 功能描述:SOT23 TO DIP ADAPTER ADAPTER 制造商:MCM 功能描述:SOT23 TO DIP ADAPTER ADAPTER
SOT23ESD-A 制造商:未知厂家 制造商全称:未知厂家 功能描述:Surface Mount Transient Voltage Suppressors
SOT23F 制造商:ZETEX 制造商全称:ZETEX 功能描述:Surface mounted, 3 pin package